Car Battery Installation Steps

Check battery height to ensure there is sufficient bonnet clearance. Dispose of Old Battery.


How To Jump Start A Car Connect Jumper Cables Printable Jump A Car Battery Car Hacks Car Battery

Take the battery out of the battery tray.

. Look for the battery in one corner of the engine bay either near the windshield or the front bumper on either side of the car. Select the Right Battery STEP TWO. Save On Your Next Car Battery Replacement.

Incorrect sizes can damage the points of contact and make the. Find the rectangular battery box which has 2 cables attached to it. Select the Best Car Battery for You.

Using a combination wrench or a socket and ratchet remove the battery hold-down clamp. Check your owners manual for the original equipment OE manufacturers recommendations for. You should also measure your batterys output using a multimeter which is designed to monitor car battery health.

The next step in proper battery installation is finding the right battery for your vehicle. Set the old battery aside and place your new battery on the tray. Re-install the clamps the same way you removed.

Check cables and connectors. Make sure the terminals are facing the right way. Disconnect the positive terminal after the negative terminal.

Install the New Battery STEP FOUR. If the battery has a handle use that instead. Cable clamp nuts and side terminal connections should be loosened and tightened with the correct size wrench.

Remove the Old Battery STEP THREE. Some car batteries use a metal hook you can loosen and tighten by hand while others may use a metal or rubber strap. This precaution is necessary to avoid damage to wiring and the battery by accidentally grounding tools.

You may need to use a ratchet to loosen and remove the clamp. Remove the negative - terminal first. Disconnect the negative battery cable end from the negative battery terminal post.

Place the new battery in the battery tray aligning the red positive and black negative ends of the battery with the matching terminals. If theres wear or damage replace them. Look for a black cable and a minus - symbol.

The battery will be marked with a - minus sign near that post. Be sure to wear gloves and goggles. If you have a newer car the battery might be underneath a plastic cover so remove the cover if necessary.

Tighten each cable end and test the new battery by turning the ignition key on. Install the new battery in the car. Start with the negative terminal and disconnect the negative battery cable.

If your terminals are too corroded already heres how to replace car battery terminals. Connect the hold-down clamp. Replacing one is a relatively simple job that generally requires only a.

Dont Get Stranded With A Dead Car Battery. Positive terminal has a plus sign and the. Place the new battery in place.

Undo hold down clamp and remove the battery from the vehicle. If not simply clean the connectors with a wire brush. Batteries are heavy so grab from the bottom using both hands.

Each post is different in size so youll need to be sure the cables fit the right posts. Once the clamp is off move it safely out of the way. Thats all there is to it.

Connect the positive red terminal to the new battery. Connect the negative black terminal to the new battery. Install the battery hold-down.

Start your car and make sure everything is working properly. Loosen the battery cable end just enough to slip it off and move it to the side out of your. Detach the positive red battery cable from the battery using the same method.

Look for the strap or hook in your vehicle and then use it to secure the battery in place. Ad Quality Service You Can Trust At A Fair Price. To install your new battery first make sure you never work on or near a battery without carefully adhering to all safety precautions and that you have all the proper tools to get the job done.

Next turn on your car and try any of the electric or electronic systems like AC or radio to make sure they work. Before proceeding double check that your car battery is connected correctly. Smear petroleum jelly on the battery terminals it will help slow corrosion.

Fit the end of the battery cables one at a time onto the new battery posts. The battery provides electricity to the starter and ignition system to get you going. Apply a thin layer of grease to the battery posts and terminals before connecting the positive terminal to the positive post first.

Once youre done all you have to do is make sure to recycle your. Remove the positive terminal. Use a solution of baking soda and water.

Battery Basics -Charging -Maintenance Storage -Installation Replacement -Warranty -Manuals - STEP ONE. Remove the plastic caps that cover the battery posts and install the anti-corrosion washers over them. You may need to clean the battery tray.

Call Us Or Make A Reservation Online. Check the cables and connectors. Remove the old battery from the car.

Installation Step 2.


Simple And Step By Step Guide On How To Jump Start A Car If Your Car Battery Is Dead Mybatterycare Car Battery Recondition Batteries Jump A Car Battery


Reconnecting Car Battery Car Battery Diy Step By Step Car Mechanic


Informative Visualization Of Car Battery Maintenance This Infographic Breaks Down Car Battery Maintenance Into 5 Steps Car Maintenance Car Care Tips Diy Car


If You Really Want To Do Diy Jump Start Please Follow Steps Here For Professional Grade Service Call Fastfix At 81145 Helpful Hints Positivity Black Cables

No comments for "Car Battery Installation Steps"